SuperSteer® Bell Crank & Bell Crank Arm Steering Controls
Now, you can help eliminate “white knuckle” RV steering, road wander and rut tracking with SuperSteer® Bell Crank steering controls
Drive more relaxed. SuperSteer® Bell Cranks (P3032) & (SS100) reduce RV steering wheel free-play and help minimize constant correction. By test, a coach performs “better than new”
Henderson’s designed the P-3032 Bell Crank (pictured above) to fit motorhomes for the Chevy/Workhorse P30 & P32 chassis. The P3032 also fits the G30HD & G3500HD Chassis.
The SuperSteer® SS100 Bell Crank (pictured right) is designed for the Freightliner XC and Magnum chassis.
Heavy-Duty Engineering
Both the P-3032 and the SS100 offer similar precision engineering that give you tighter motorhome steering control and longer life than OEM parts.
These Bell Cranks feature:
- Chromemoly heat-treated steel shaft.
- Hi-tensile strength casting, spindle & tapered Timken roller
bearings. - Grease-packed & sealed to keep out dirt and water for life.
- You can adjust these bell cranks to return them to like-new performance.
- They’re maintenance-free.
Comparison
● Pictured left - Factory OEM bell
crank. Note the use of sleeve bushing.
● Pictured right - P30-32 Bell Crank. Note the use of
tapered bearings
protected inside
the sealed unit.
Why SuperSteer® Steering Controls Work So Well
Straight bushings in standard bell cranks can’t be preloaded like a tapered roller bearing. This means a certain amount of clearance always allows play between the bushing and shaft.
The Difference: The SuperSteer® Bell Crank uses tapered roller bearings on a hi-strength steel shaft. It’s installed with a pre-load so it’s much tighter and allows far less wear.
Endurance Tested: A test proved these Bell Cranks 19% tighter than a set of rebuilt bell cranks with simple bushings. The high-quality tapered roller bearings remain tight with no lateral (side-to-side) or vertical movement after testing. The SuperSteer® unit outlasted the OEM unit many times over, which justifies its lifetime warranty.
Drivers Who Installed Them Are
Sold On SuperSteer®
Sold On SuperSteer®
After a SuperSteer® installation, one motorhome owner commented his motorhome steering control was much tighter and more responsive. More important, he felt considerably less fatigued after driving.
Bud Weisbrod has some choice
thoughts about bell cranks here.
SuperSteer® increases motorhome steering control noticeably over stock OEM bell cranks.
Life-Long Warranty
These SuperSteer® Bell Cranks are warranted as long as you own your coach.
Henderson’s Guarantee If you decide to have your bell cranks installed at Henderson’s, we also guarantee our work risk-free. If you’re not satisfied, you get your money back.
SuperSteer Bell Cranks work. “Hooray, the wandering steering on my Trek 24 has been fixed. First, I put on your SuperSteer® bellcrank support and there was a noticeable improvement. Then I had it aligned using Henderson’s settings (quite different from Chevrolet’s) and I am satisfied.” Robert Hayward, Seattle, WA
With this improved design, you drive relaxed while maintaining crisp, precise RV steering and control in high wind and road ruts. You steer your rig with much less fatigue, and the system requires virtually no more attention.
SuperSteer® Bell Crank Arms
“We leave nothing to chance”
It may seem unimportant, but this little gadget is a vital part of your steering system. In addition to the Bell Crank, the Bell Crank Arm must be checked to make sure it’s tight and doesn’t allow play.
The bell crank arm can contribute to less responsive steering. We always recommend you have this pivotal joint checked for wear and replacement if needed.
These units available –
- P3032 Bell Crank Chevy/Workhorse P30, P32, G30HD & G3500HD chassis
- SS100 Bell Crank Freightliner chassis
- SS3032-10D - Driver Bell Crank Arm
- SS3032-10P - Passenger Bell Crank Arm
If you’re within driving distance of Grants Pass, Oregon, you can have our trained Henderson’s Line-Up technicians install this equipment for you. If not, you may install them yourself or get the location of the nearest SuperSteer® dealer. Just phone us at 888-898-3281 or E-mail us below.
SuperSteer® Manufacturing & Distribution is a division of Henderson’s Line-Up, Brake &
RV, Inc.
SuperSteer®
Division of Henderson's Line-Up
458 Redwood Highway
Grants Pass, OR 97527
- Phone us at: 541-955-0769
- “800″ Phone: Toll-free - 888-898-3281
- Fax us at: 541-476-3851
- SuperSteer Tech Line: 541-955-0769
- SuperSteer Order Line: Toll-free - 888-898-3281
- Office Hours: (PST) 7 a.m. - 4 p.m. Mon-Fri; Closed Noon
to 1 p.m. If you call after hours, we'll call you back. If you’re driving & unfamiliar with the Grants Pass area, see a map here
E-mail us and tell us what you need at:
Monday - Friday 7 A.M. to 4 P.M.
Closed Noon to 1 P.M.
Share this:
